Adiabatic flame temperature

Adiabatic flame temperature

In the study of combustion, there are two types of adiabatic flame temperature depending on how the process is completed: constant volume and constant pressure. The constant volume adiabatic flame temperature is the temperature that results from a complete combustion process that occurs without any work, heat transfer or changes in kinetic or potential energy.

The constant pressure adiabatic flame temperature is the temperature that results from a complete combustion process that occurs without any heat transfer or changes in kinetic or potential energy. Its temperature is lower than the constant volume process because some of the energy is utilized to change the volume of the system (i.e., generate work).

(It is a common fallacy that this is the maximum temperature that can be achieved for given reactants because any heat transfer from the reacting substances and/or any incomplete combustion would tend to lower the temperature of the products. However, since the assumptions inherent in the adiabatic flame temperature assume chemical equilibrium, states in thermal equilibrium but not chemical equilibrium are not constrained by this limit. In fact, several fuel rich acetylene and methane flames have been found to exceed their adiabatic flame temperatures by hundreds of degrees.)

Common flames

In daily life, the vast majority of flames one encounters are those of organic compounds including wood, wax, fat, common plastics, propane, and gasoline. The constant-pressure adiabatic flame temperature of such substances in air is in a relatively-narrow range around 1950°C. This is because, in terms of stoichiometry, the combustion of an organic compound with "n" carbons involves breaking roughly 2"n" C–H bonds, "n" C–C bonds, and 1.5"n" O2 bonds to form roughly "n" CO2 molecules and "n" H2O molecules.

Because most combustion processes that happen naturally occur in the open air, there is nothing that confines the gas to a particular volume like the cylinder in an engine. As a result, these substances will burn at a constant pressure allowing the gas to expand during the process.

Common flame temperatures

Assuming initial atmospheric conditions (1 bar and 20°C), the following table list the adiabatic flame temperature for various gases under constant volume conditions. The temperatures mentioned here are for a stoichiometric fuel-oxidizer mixture (i.e. equivalence ratio phi = 1).

Thermodynamics

From the first law of thermodynamics for a closed reacting system we have,:{}_RQ_P - {}_RW_P = U_P - U_R where, {}_RQ_P and {}_RW_P are the heat and work transferred during the process respectively, and U_R and U_P are the internal energy of the reactants and products respectively. In the constant volume adiabatic flame temperature case, the volume of the system is held constant hence there is no work occurring,: {}_RW_P = intlimits_R^P {pdV} = 0 and there is no heat transfer because the process is defined to be adiabatic: {}_RQ_P = 0 . As a result, the internal energy of the products is equal to the internal energy of the reactants: U_P = U_R . Because this is a closed system, the mass of the products and reactants is constant and the first law can be written on a mass basis,: U_P = U_R Rightarrow m_P u_P = m_R u_R Rightarrow u_P = u_R .

In the constant pressure adiabatic flame temperature case, the pressure of the system is held constant which results in the following equation for the work,: {}_RW_P = intlimits_R^P {pdV} = pleft( {V_P - V_R } ight) Again there is no heat transfer occurring because the process is defined to be adiabatic: {}_RQ_P = 0 . From the first law, we find that,: - pleft( {V_P - V_R } ight) = U_P - U_R Rightarrow U_P + pV_P = U_R + pV_R Recalling the definition of enthalpy we recover: H_P = H_R . Because this is a closed system, the mass of the products and reactants is constant and the first law can be written on a mass basis,: H_P = H_R Rightarrow m_P h_P = m_R h_R Rightarrow h_P = h_R .

We see that the adiabatic flame temperature of the constant pressure process is lower than that of the constant volume process. This is because some of the energy released during combustion goes into changing the volume of the control system. One analogy that is commonly made between the two processes is through combustion in an internal combustion engine. For the constant volume adiabatic process, combustion is thought to occur instantaneously when the piston reaches the top of its apex (Otto cycle or constant volume cycle). For the constant pressure adiabatic process, while combustion is occurring the piston is moving in order to keep the pressure constant (Diesel cycle or constant pressure cycle).

If we make the assumption that combustion goes to completion (i.e. CO_2 and H_2O), we can calculate the adiabatic flame temperature by hand either at stoichiometric conditions or lean of stoichiometry (excess air). This is because there are enough variables and molar equations to balance the left and right hand sides,

:{ m{C_alpha { m{H_eta { m{O_gamma { m{N_delta + left( {a{ m{O_{ m{2 + b{ m{N_{ m{2 } ight) o u _1 { m{CO_{ m{2 + u _2 { m{H_{ m{2 { m{O + u _3 { m{N_{ m{2 + u _4 { m{O_{ m{2

Rich of stoichiometry there are not enough variables because combustion cannot go to completion with at least CO and H_2 needed for the molar balance (these are the most common incomplete products of combustion),

: { m{C_alpha { m{H_eta { m{O_gamma { m{N_delta + left( {a{ m{O_{ m{2 + b{ m{N_{ m{2 } ight) o u _1 { m{CO_{ m{2 + u _2 { m{H_{ m{2 { m{O + u _3 { m{N_{ m{2 + u _5 { m{CO + u _6 { m{H_{ m{2

However, if we include the Water gas shift reaction,: { m{CO_{ m{2 + H_2 Leftrightarrow { m{CO + { m{H_{ m{2 { m{O and use the equilibrium constant for this reaction, we will have enough variables to complete the calculation.

Different fuels with different levels of energy and molar constituents will have different adiabatic flame temperatures.

We can see by the following figure why nitromethane (CH_3NO_2) is often used as a power boost for cars. Since it contains two moles of oxygen in its molecular makeup, it can burn much hotter because it provides its own oxidant along with fuel. This in turn allows it to build-up more pressure during a constant volume process. The higher the pressure, the more force upon the piston creating more work and more power in the engine. It is interesting to note that it stays relatively hot rich of stoichiometry because it contains its own oxidant. However, continual running of an engine on nitromethane will eventually melt the piston and/or cylinder because of this higher temperature.

In real world applications, complete combustion does not typically occur. Chemistry dictates that dissociation and kinetics will change the relative constituents of the products. There are a number of programs available that can calculate the adiabatic flame temperature taking into account dissociation through equilibrium constants (Stanjan, NASA CEA, AFTP). The following figure illustrates that the effects of dissociation tend to lower the adiabatic flame temperature. This result can be explained through Le Chatelier's principle.

ee also

*Adiabatic process
*Flame speed

References

External links

General information

* Cite web
last = Babrauskas
first = Vytenis
title = Temperatures in flames and fires
work = Fire Science and Technology Inc.
accessdate = 2008-01-27
date = 2006-02-25
url = http://www.doctorfire.com/flametmp.html

* [http://web.mit.edu/16.unified/www/SPRING/propulsion/notes/node111.html Adiabatic Flame Temperature]

Tables

* Cite web
title = Adiabatic Flame Temperature
work = The Engineering Toolbox
accessdate = 2008-01-27
url = http://www.engineeringtoolbox.com/adiabatic-flame-temperature-d_996.html
adiabatic flame temperature of hydrogen, methane, propane and octane with oxygen or air as oxidizers
* Cite web
title = Flame Temperatures for some Common Gases
work = The Engineering Toolbox
accessdate = 2008-01-27
url = http://www.engineeringtoolbox.com/flame-temperatures-gases-d_422.html

* [http://hypertextbook.com/facts/1998/JamesDanyluk.shtml Temperature of a blue flame and common materials]

Calculators

* [http://www.depcik.com/eduprograms/aftp.htm Adiabatic flame temperature program]
* [http://www.gaseq.co.uk Gaseq] , program for performing chemical equilibrium calculations.
* [http://astronautics.usc.edu/utility/flame_temperature/ Flame Temperature Calculator] - Constant pressure bipropellant adiabatic combustion
* [http://www.engr.colostate.edu/~allan/thermo/page12/adia_flame/Flamemain.html Adiabatic Flame Temperature calculator]


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Adiabatic process — This article covers adiabatic processes in thermodynamics. For adiabatic processes in quantum mechanics, see adiabatic process (quantum mechanics). For atmospheric adiabatic processes, see lapse rate. In thermodynamics, an adiabatic process or an …   Wikipedia

  • Flame speed — The flame speed is the measured rate of expansion of the flame front in a combustion reaction. Whereas flame speed is generally used for a fuel, a related term is explosive velocity, which is the same relationship measured for an explosive.… …   Wikipedia

  • Orders of magnitude (temperature) — Temperature in °C compared to the thermodynamic scale in electron volts, which are also used as a unit of temperature. List of orders of magnitude for temperature Factor Multiple Item 10−∞ 0 K …   Wikipedia

  • Адиабатическое горение — экзотермическая химическая реакция, происходящая при постоянном давлении или объеме, при которой исключена потеря энергии в окружающую среду. Температура адиабатического горения при постоянном давлении ниже температуры горения при постоянном… …   Википедия

  • Combustion — This article is about the process of burning. For combustion without external ignition, see spontaneous combustion. For the engine used in mobile propulsion, see internal combustion engine. For the visible part of a fire, see flame. Burning… …   Wikipedia

  • Oxyhydrogen — Knallgas redirects here. For bacteria which oxidize hydrogen, see Knallgas bacteria. Nineteenth century electrolytic cell for producing oxyhydrogen. Oxyhydrogen is a mixture of hydrogen (H2) and oxygen (O2) gases, typically in a 2:1 molar ratio,… …   Wikipedia

  • Diesel cycle — Thermodynamics …   Wikipedia

  • Internal combustion engine — The internal combustion engine is an engine in which the combustion of a fuel (normally a fossil fuel) occurs with an oxidizer (usually air) in a combustion chamber. In an internal combustion engine, the expansion of the high temperature and high …   Wikipedia

  • Nitromethane — IUPAC name …   Wikipedia

  • Exhaust gas recirculation — (EGR) is a nitrogen oxide (NOx) emissions reduction technique used in most gasoline and diesel engines.EGR works by recirculating a portion of an engine s exhaust gas back to the engine cylinders. Intermixing the incoming air with recirculated… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”